Welcome Guest
SHOP BY CATEGORY
SHOP BY BRAND
SHOP BY VEHICLE
Sales Support 877-474-4821
877-260-5452
Call Our Stateside Experts!
Direct Fit 35 Splines None 35 Splines
Direct Fit 35 Splines None On Sale
2 Product Groups
Switch to View Products
TeraFlex CRD60 HD Axle Assemblies
TeraFlex CRD60 Axle AssembliesFrom $2,719.99
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in “skimmer” cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4”-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted applications
- Features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
From $2,719.99
TeraFlex Tera60 HD Axle Assemblies
TeraFlex Tera60 HD Axle AssembliesFrom $7,254.99
- 3.25” O.D. x 0.375” wall DOM axle tube for superior strength vs. weight
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- High-flow oil passages
- ottom oil drain hole for simple fluid changes
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4”-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2” compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted applications
- Features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
From $7,254.99
7 Products
Switch to View Product Groups
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex CRD60 HD Rear Axle with Semi-Float - 3460000
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 1 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Models with 4-6" lift
- This much lift REQUIRES adjustable control arms for caster angle adjustments
- Does not include gears, locker or carrier
- Factory-style semi-float design
- 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
- 67" WMS-WMS and 5x5" wheel bolt pattern
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- Includes 1350 series pinion yoke
- 35-spline inner and outer axle shafts
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- 1-Year/Unlimited Mileage Warranty
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$2,719.99
Only 1 left in Stock ?
$2,719.99
Only 1 left in Stock
?
LOW PRICE GUARANTEE
EASY RETURNS
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 1 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Models with 4-6" lift
- This much lift REQUIRES adjustable control arms for caster angle adjustments
- Does not include gears, locker or carrier
- Factory-style semi-float design
- 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
- 67" WMS-WMS and 5x5" wheel bolt pattern
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- Includes 1350 series pinion yoke
- 35-spline inner and outer axle shafts
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- 1-Year/Unlimited Mileage Warranty
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex CRD60 HD 67" Rear Axle Assembly with Full-Float Axles - 3470000
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 2 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Bare housing - does not include ring and pinion, locker or carrier
- Models with 4-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kit, full-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
- Extreme duty full-float design
- Includes Rear Performance Big Rotor Kit with 13.5" Vented Rotors
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$5,166.99
Only 2 left in Stock ?
$5,166.99
Only 2 left in Stock
?
LOW PRICE GUARANTEE
EASY RETURNS
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 2 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Bare housing - does not include ring and pinion, locker or carrier
- Models with 4-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kit, full-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
- Extreme duty full-float design
- Includes Rear Performance Big Rotor Kit with 13.5" Vented Rotors
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex Tera60 HD 70" Front Axle Assembly with Locking Hubs - 36700004
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 1 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Front axle housing - does not include gears, carrier or bearings
- Models with 4-6" lift
- 8x6.5 bolt pattern
- Measures 70" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, 35-spline inner and outer axle shafts, Spicer HD Ball Joints, 1350 series pinion yoke, HD Drag Link Flip Kit and HD Tie Rod Kit and Front Big Brake Kit with Vented Rotors
- Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- Bottom oil drain hole for simple fluid changes
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$8,842.99
Only 1 left in Stock ?
$8,842.99
Only 1 left in Stock
?
LOW PRICE GUARANTEE
EASY RETURNS
How to Get it
Free! Curbside & In-Store Pickup: Select A Store Near You
Ship to Home:
Only 1 left in Stock ?- Fitment: Direct Fit
- 07-18 Wrangler JK, 2 & 4 Door
- Front axle housing - does not include gears, carrier or bearings
- Models with 4-6" lift
- 8x6.5 bolt pattern
- Measures 70" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, 35-spline inner and outer axle shafts, Spicer HD Ball Joints, 1350 series pinion yoke, HD Drag Link Flip Kit and HD Tie Rod Kit and Front Big Brake Kit with Vented Rotors
- Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- Bottom oil drain hole for simple fluid changes
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted JK applications
- 4-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all JK ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex Tera60 HD Front Axle with Unit Bearing - 3860000
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Models with 3-6" lift
- Does not include gears, locker or carrier
- Requires driveshaft modifications
- Sealed unit bearing assembly for long-term maintenance-free dependability
- 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
- 63.5" WMS-WMS and 5x5.5" wheel bolt pattern
- Includes Front Big Brake Kit with 13.3" Vented Rotors
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Includes 1350 series pinion yoke
- 35-spline inner and outer axle shafts
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- High-flow oil passages
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- 1-Year/Unlimited Mileage Warranty
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$7,254.99
On Backorder
Contact Us for Availability or Alternatives
LOW PRICE GUARANTEE
EASY RETURNS
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
$7,254.99
On Backorder
Contact Us for Availability or Alternatives
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Models with 3-6" lift
- Does not include gears, locker or carrier
- Requires driveshaft modifications
- Sealed unit bearing assembly for long-term maintenance-free dependability
- 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
- 63.5" WMS-WMS and 5x5.5" wheel bolt pattern
- Includes Front Big Brake Kit with 13.3" Vented Rotors
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Includes 1350 series pinion yoke
- 35-spline inner and outer axle shafts
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- High-flow oil passages
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- 1-Year/Unlimited Mileage Warranty
- California Residents: WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex Tera60 HD 67" Front Axle Housing with Locking Hubs - 3870000
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Front axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, 35-spline inner and outer axle shafts, Spicer HD ball joints, 1350 series pinion yoke and Front Big Brake Kit with Vented Rotors
- Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$8,596.99
On Backorder
Contact Us for Availability or Alternatives
LOW PRICE GUARANTEE
EASY RETURNS
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
$8,596.99
On Backorder
Contact Us for Availability or Alternatives
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Front axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, 35-spline inner and outer axle shafts, Spicer HD ball joints, 1350 series pinion yoke and Front Big Brake Kit with Vented Rotors
- Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
- Fixed spindle mount hub assembly
- Tera60 specific high-pinion front axle housing design
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- HD forged inner knuckles with greater upper and lower section strength
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover
- Smooth radius bottom design to glide over rocks and obstacles
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced front track bar mount (ties into spring pad) for greater strength
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex CRD60 HD 67" Rear Axle Housing with Full-Float Axles - 3900000
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Rear axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, full-float axles, 35-spline inner and outer axle shafts, Spicer HD ball joints, 1350 series pinion yoke and Rear Big Brake Kit with Vented Rotors
- Factory-style Full-Float design
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in "skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$5,658.99
On Backorder
Contact Us for Availability or Alternatives
LOW PRICE GUARANTEE
EASY RETURNS
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
$5,658.99
On Backorder
Contact Us for Availability or Alternatives
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Rear axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Spicer bearings and install kits, full-float axles, 35-spline inner and outer axle shafts, Spicer HD ball joints, 1350 series pinion yoke and Rear Big Brake Kit with Vented Rotors
- Factory-style Full-Float design
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in "skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
4WP PROTECTION PLAN
Our Protection Plan covers your investment above and beyond the manufacturer's coverage. For only 10% more, if your item is damaged, fails or malfunctions, we'll replace it for free!
Sign In Or Create an Account
Reset Password
An email is sent to .
Enter email address to change your password
After you submit your email address, you'll receive an email a link that will let you change your password.
Choose Your Secure Checkout Method
Create An Account
Add to Wishlist
TeraFlex CRD60 HD 67" Rear Axle Housing with Full-Float Axles and Pro LCG Truss - 3980000
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Rear axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Pro LCG Rear Axle Truss, Spicer bearings and install kits, full-float axles, 35-spline inner and outer axle shafts, 1350 series pinion yoke and Rear Big Brake Kit with Vented Rotors
- Factory-style Full-Float design
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in "skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
$5,658.99
On Backorder
Contact Us for Availability or Alternatives
LOW PRICE GUARANTEE
EASY RETURNS
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
TeraFlex CRD60 HD 67" Rear Axle Housing with Full-Float Axles and Pro LCG Truss - 3980000
Part #: TER3980000$5,658.99
On Backorder
Contact Us for Availability or Alternatives
Email me when this product comes in stock
LOW PRICE GUARANTEE
EASY RETURNS
- Fitment: Direct Fit
- 97-06 Wrangler TJ/LJ
- Rear axle housing - does not include gears, carrier or bearings
- Models with 3-6" lift
- 8x6.5 bolt pattern
- Measures 67" WMS-WMS
- Axle tube: 3.25" x 0.375"
- Includes Pro LCG Rear Axle Truss, Spicer bearings and install kits, full-float axles, 35-spline inner and outer axle shafts, 1350 series pinion yoke and Rear Big Brake Kit with Vented Rotors
- Factory-style Full-Float design
- Fixed spindle mount hub assembly
- Tera CRD60 specific high-pinion rear axle housing design
- HD bearing caps increase rigidity and reduce ring and pinion distortion
- Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
- Built-in "skimmer" cuts ring gear oil halo and forces it into the pinion bearings
- Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
- Oversized outer pinion bearing handles increased torque and high-load conditions
- High-capacity housing holds maximum amount of oil
- Asymmetric housing design for extra-long tube side strength
- Pre-installed inner axle seals
- Ductile cast iron housing with increased rib gussets
- HD ductile iron differential cover with increased cover mounting area
- Integrated lower control arm skid plates
- High-flow oil passages
- Bottom oil drain hole for simple fluid changes
- Reinforced rear track bar mount with multiple mounting locations
- UV protected triple-stage powder coat for corrosion resistance
- 1/4"-thick CNC laser cut axle brackets for extreme strength
- Pre-installed upper control arm bushings
- Proper pinion angle for lifted TJ applications
- 3-6" Lift features a raised pinion angle and raised track bar bracket
- Pre-tapped hole on spring perch for bump stop extensions
- Pre-drilled holes for limit straps and lower spring retainers
- Retains all TJ ESP, ABS, and speedometer sensor capability
- 100% engineered, designed, and built in the USA with new components
- California Residents:WARNING + View More Specs - View Less Specs
PROMOTIONS AUTOMATICALLY APPLIED
We Pay the Sales Tax - 4th Of July Sale Weekend At 4WP!
Lowest Price! Guaranteed! Request A Price Match
