TeraFlex CRD60 HD Rear Axle with Semi-Float - 3460000

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Models with 4-6" lift
• This much lift REQUIRES adjustable control arms for caster angle adjustments
• Does not include gears, locker or carrier
• Factory-style semi-float design
• 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
• 67" WMS-WMS and 5x5" wheel bolt pattern
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• Includes 1350 series pinion yoke
• 35-spline inner and outer axle shafts
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• 1-Year/Unlimited Mileage Warranty
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex CRD60 HD 67" Rear Axle Assembly with Full-Float Axles - 3470000

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Bare housing - does not include ring and pinion, locker or carrier
• Models with 4-6" lift
• 8x6.5 bolt pattern
• Measures 67" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes Spicer bearings and install kit, full-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
• Extreme duty full-float design
• Includes Rear Performance Big Rotor Kit with 13.5" Vented Rotors
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex Tera60 HD 70" Front Axle Assembly with Locking Hubs and ARB Air Locker (4.88 Gears) - 36064884

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Front axle assembly with 4.88 Super 60 ring and pinion, lock out hubs and ARB Air Locker
• Models with 4-6" lift
• 8x6.5 bolt pattern
• Measures 70" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes Spicer bearings and install kit, 35-spline inner and outer axle shafts, Spicer HD Ball Joints, 1350 series pinion yoke, HD Drag Link Flip Kit and HD Tie Rod Kit and Front Big Brake Kit with Vented Rotors
• Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages
• ottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents:WARNING
+ View More Specs - View Less Specs

TeraFlex Tera60 HD 70" Front Axle Assembly with Locking Hubs - 36700004

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Front axle housing - does not include gears, carrier or bearings
• Models with 4-6" lift
• 8x6.5 bolt pattern
• Measures 70" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes Spicer bearings and install kits, 35-spline inner and outer axle shafts, Spicer HD Ball Joints, 1350 series pinion yoke, HD Drag Link Flip Kit and HD Tie Rod Kit and Front Big Brake Kit with Vented Rotors
• Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• Bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents:WARNING
+ View More Specs - View Less Specs

TeraFlex TJ Dana 60 Rear Axle Assembly 4.88 Ratio 35 Spline With ARB Air Locker - 3311488

• Fitment: Direct Fit
• 4.88 Gear Ratio
• ARB Air Locker Differential
• 35 Spline Axle Shafts
• Disc Brake Upgrade With Parking Brake
• May Require Driveshaft Modifications
• Compressor Sold Separately
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex TJ Dana 60 Rear Axle Assembly 4.56 Ratio 35 Spline With ARB Air Locker And Pro LCG Truss - 3321456

• Fitment: Direct Fit
• 4.56 Gear Ratio
• ARB Air Locker Differential
• 35 Spline Axle Shafts
• Disc Brake Upgrade With Parking Brake
• Heavy Duty LGC Truss For custom 4 Link Suspensions
• May Require Driveshaft Modifications
• Compressor Sold Separately
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex TJ Dana 60 Rear Axle Assembly 5.13 Ratio 35 Spline With ARB Air Locker And Pro LCG Truss - 3321513

• Fitment: Direct Fit
• 5.13 Gear Ratio
• ARB Air Locker Differential
• 35 Spline Axle Shafts
• Disc Brake Upgrade With Parking Brake
• Heavy Duty LGC Truss For custom 4 Link Suspensions
• May Require Driveshaft Modifications
• Compressor Sold Separately
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex CRD60 HD 70" Rear Axle Assembly with Full-Float Axles and ARB Air Locker (4.88 Gears) - 34064884

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Rear axle assembly with 4.88 ring and pinion and ARB Super 60
• Models with 4-6" lift
• 8x6.5 bolt pattern
• Measures 70" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes ARB air locker, Spicer Super 60 ring and pinion, Spicer bearings and install kit, full-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
• Includes Rear Performance Big Rotor Kit with 13.5" Vented Rotors
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• Includes 1350 series pinion yoke
• 35-spline inner and outer axle shafts
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• California Residents: WARNING
+ View More Specs - View Less Specs

RCV Axles Ultimate Dana 60 CV Axle for Ford F-250/350 - Standard Dana 60 with 35 Spline Diff. - CVJ60-F2501

• Fitment: Direct Fit
• 99-04 Ford F-250/F-350 with Dana 60 and 35 spline center section
• Includes front left and right axles
• Does not fit 30 spline Dana 50 center section on 00-02 models
• 35 spline inner and outer
• Left inner axle length: 15.38"
• Right inner axle length: 37.75"
• Outer stub axle length: 9.39"
• California Residents: WARNING
+ View More Specs - View Less Specs

RCV Axles Ultimate IFS CV Axle Set - CVJIFS-TOY2X2

• Fitment: Direct Fit
• 4WD models
• Front CV axle set
• For vehicles with +2 inch All Pro Long Travel Suspension
• 300M internal components
• Meets and exceeds the strength of a straight axle swap
• California Residents: WARNING
+ View More Specs - View Less Specs

Dynatrac Dana 44 Rear Axle Shaft Upgrade - JK44-1X4234-B

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Does not fit Rubicon models
• Dana 44 rear axle
• 35 spline shaft
• 5x5 and 5x5.5 bolt patterns
• New carrier required - sold separately
• Includes tone ring
• New wheel studs, bearings and seals are included
• Made in the USA
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex CRD60 HD 67" Rear Axle Assembly with Semi-Float Axles and ARB Air Locker (4.30 Gears) - 3446430

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Rear axle assembly with 4.30 ring and pinion and ARB Super 60
• Models with 4-6" lift
• 5x5 bolt pattern
• Measures 67" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes ARB Air Locker, Spicer Super 60 ring and pinion, Spicer bearings and install kit, semi-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
• Factory-style semi-float design
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex CRD60 HD Rear Axle with Semi-Float and 4.88 Gears and ARB Locker - 3446488

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Models with 4-6" lift
• This much lift REQUIRES adjustable control arms for caster angle adjustments
• Factory-style semi-float design
• 3.25" O.D. x 0.375" wall DOM axle tube for superior strength vs. weight
• 67" WMS-WMS and 5x5" wheel bolt pattern
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• Includes 1350 series pinion yoke
• 35-spline inner and outer axle shafts
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• 1-Year/Unlimited Mileage Warranty
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex CRD60 HD 67" Rear Axle Assembly with Semi-Float Axles and ARB Air Locker (5.38 Gears) - 3446538

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Rear axle assembly with 4.30 ring and pinion and ARB Super 60
• Models with 4-6" lift
• 5x5 bolt pattern
• Measures 67" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes ARB Air Locker, Spicer Super 60 ring and pinion, Spicer bearings and install kit, semi-float axles, 35-spline inner and outer axle shafts and 1350 series pinion yoke
• Factory-style semi-float design
• Fixed spindle mount hub assembly
• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in skimmer" cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket (where applicable)
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents: WARNING
+ View More Specs - View Less Specs

TeraFlex Tera60 HD 70" Front Axle Assembly with Locking Hubs and ARB Air Locker (4.30 Gears) - 36064304

• Fitment: Direct Fit
• 07-18 Wrangler JK, 2 & 4 Door
• Front axle assembly with 4.30 Super 60 ring and pinion, lock out hubs and ARB Air Locker
• Models with 4-6" lift
• 8x6.5 bolt pattern
• Measures 70" WMS-WMS
• Axle tube: 3.25" x 0.375"
• Includes Spicer bearings and install kit, 35-spline inner and outer axle shafts, Spicer HD Ball Joints, 1350 series pinion yoke, HD Drag Link Flip Kit and HD Tie Rod Kit and Front Big Brake Kit with Vented Rotors
• Sealed SlimLock Locking Hub Assembly for long-term maintenance-free dependability
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages
• ottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4"-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2" compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted JK applications
• 4-6" Lift features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all JK ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components
• California Residents:WARNING
+ View More Specs - View Less Specs

TeraFlex Tera60 HD 70" Front Axle Assembly with Locking Hubs and ARB Air Locker (5.38 Gears) - 36065384