Dana Spicer Dana 44 Front Axle Assemblies

From $4,134.99

• Genuine Spicers gears
• Thick axle tubes for improved strength
• Redesigned and thicker brackets
• Spicer chromoly axle shafts
• Performance differential cover and Spicer performance gasket
• Increased gross axle weight rating
• California Residents: WARNING

Dana Spicer Ultimate Dana 60 Axle Assemblies

From $8,499.99

• The strongest, most robust axle assembly on the market
• Massive Spicer SPL 70 u-joints—exclusive to Dana
• Provides optimal performance for lifted vehicles with larger tires
• Improved “rock solid” seals for optimal protection from environmental contamination
• Manufactured from cold-forged steel
• Spicer 35 spline SAE-4340 nickel chromoly steel axle shafts
• Warn 35 spline hub locks
• Allowing for wheel bearings to be serviced individually
• Easier to repair and service than unit bearing design
• High-strength, heavy gauge brackets
• Cover face rotated back for greater ground clearance
• Reinforced ribbing on bottom of carrier to prevent hang-ups on rocks or rough terrain
• Selectable electronic locking differentials
• Precision-forged gears offer ideal meshing, strength and durability
• Upper and lower control arms in same location as OE
• Better fit, less adjustment on control arm
• Genuine Made in the USA Spicer® 10" (256 mm) ring and pinion gear
• Precision heat treated for optimal hardness and durability
• Face hobbed for precise mating of gear teeth and a quieter ride
• Lapped to reduce noise and heat
• Spicer 1350 Strap-style/Half-round end yoke
• Axle tubes: 3.5" tube diameter/.370" wall thickness
• Helps prevent steering from being knocked out of alignment
• California Residents: WARNING

Dana Spicer Ring and Pinion Kits

From $1,230.99

• Fits most 1996 and earlier standard rotation front and rear axles
• For use with 3.54 and down carrier
• Requires D/S706016X differential bearing kit to complete installation
• Includes pinion bearings
• Includes pinion seal
• Includes pinion shim pack
• Includes pinion preload shim pack or crush sleeve
• Includes pinion nut
• Includes differential shim pack
• Includes ring gear bolts
• Superior Metallurgy ensures more consistent, higher quality gears
• Hobbed and shaved gearing provides optimal mating to minimize stress and maximize life
• Precision heat-treating and shot-peening delivers consistent quality
• California Residents: WARNING

TeraFlex CRD60 HD Axle Assemblies

From $5,022.99

• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in “skimmer” cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

Motive Gear Ring and Pinion Sets

From $384.99

• Ring and Pinion Sets
• Stock performance ring and pinions
• Easy setup, superior strength, quality, and a vast ratio selection
• Backed by rigid quality control processes
• 2 year / 100,000 mile no-nonsense warranty
• California Residents: WARNING

Omix-ADA Ring And Pinions

From $669.99

• Ring And Pinion
• California Residents: WARNING

TeraFlex Dana 60 Axle Assemblies

From $5,548.99

• Maximum Ground Clearance
• Adjustable Control Arm And Track Bar Mounting Locations
• Comes complete with properly matched components
• Ultra-reliable package that exceeds stock axle performance, durability and reliability
• California Residents: WARNING

Dana Spicer Dana 60 5.38 Ratio Ring and Pinions

From $939.99

• All Dana Spicer ring gear and pinion sets are designed and tested to meet original equipment specifications
• Spicer gearing is manufactured with a special grade of steel, machined and heat-treated to precision, so you can count on optimum set-up and mating of the gears
• Dana Spicer has conducted aggressive dynamometer tests to ensure exceptional performance of all of their genuine Spicer gearing
• California Residents: WARNING

Dana Spicer Dana 50 5.38 Ratio Ring and Pinions

From $219.99

• All Dana Spicer ring gear and pinion sets are designed and tested to meet original equipment specifications
• Spicer gearing is manufactured with a special grade of steel, machined and heat-treated to precision, so you can count on optimum set-up and mating of the gears
• Dana Spicer has conducted aggressive dynamometer tests to ensure exceptional performance of all of their genuine Spicer gearing
• California Residents: WARNING

Yukon Gear & Axle Ring and Pinion Sets

From $399.89

Yukon Gear & Axle Ring and Pinion Sets with Install Kits

From $1,011.39

TeraFlex Tera44 HD Axle Assemblies

From $4,794.99

• 3.25” O.D. x 0.25” wall axle tube increases torsional strength to resist bending with minimal weight increase
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages and bottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrated factory location upper control arm mount
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Tera60 HD Axle Assemblies

From $10,943.99

• 3.25” O.D. x 0.375” wall DOM axle tube for superior strength vs. weight
• Fixed spindle mount hub assembly
• Tera60 specific high-pinion front axle housing design
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• HD forged inner knuckles with greater upper and lower section strength
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover
• Smooth radius bottom design to glide over rocks and obstacles
• Integrated lower control arm skid plates
• High-flow oil passages
• ottom oil drain hole for simple fluid changes
• Reinforced front track bar mount (ties into spring pad) for greater strength
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Integrating the front upper control arm mounts into the housing increases up travel an additional 2” compared to other aftermarket Dana 60 axles
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

USA Standard Gear Ring & Pinion Sets

From $287.89

USA Standard Gear and Install Kit Packages

From $1,599.89

• Quick Kits feature USA Standard ring and pinion gear set, Master Install kit with high quality Koyo bearings and the necessary small parts required to get vehicles off the lift and back on the road quickly
• Quick Kits provide a one-stop shopping experience that allows you to easily find the correct parts for common differential repairs at an affordable price
• The Gear and Install Kit Includes Axle Bearings & Seals
• The Gear and Install Kit Includes Yukon Dura Grip Clutch Style Limited Slip (LSD)
• All positraction units are fully rebuildable

Dana Spicer Dana 44 AdvanTEK Ring and Pinions

From $340.99

Dana Spicer Ultimate Dana 80 Axles

From $14,013.99

• Dana 80 axle model
• Chromoly axle shaft material
• Available with different traction devices
• Available for front and rear applications

Currie Enterprises Currie 44 Front Crate Axle Assemblies

From $5,600.00

• Currie 44 high-pinion nodular iron center section with thicker walls and webbing to deliver superior strength and rigidity
• Large 3-inch diameter .375 wall axle tubes (left) are more than twice as strong as the stock 2.5-inch diameter .250 wall tubes
• Currie heavy duty forged inner knuckles (right) are significantly stronger that the stock knuckles (left) and are designed for serious off-road use with up to 37” tall tires
• Currie Performance 4340 Chromoly axles provide superior strength over OEM carbon steel axles
• Upper control arm mounts feature rebuildable Johnny Joints® for improved suspension articulation
• Lower control arm mounts are one piece construction with integrated skid plates to help fend off bracket seeking rocks
• 1350 pinion yoke provides increased strength over the stock companion flange
• Currie nodular-iron differential cover to defend against those unfortunate rock encounters
• California Residents: WARNING

Currie Enterprises Currie 60 Rear Crate Axle Assemblies

From $5,800.00

• Currie 60 high-pinion, radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys can’t read a tape measure
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Large diameter pinion bearings to handle the increased load of reverse geometry gears
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues
• Large 3-inch diameter .375 thick axle tubes deliver superior strength without sacrificing ground clearance or being overweight
• Currie Performance 40-spline 4340 chrome moly semi-floating axles, the largest and strongest standard axle in the industry
• Massive Set 80 axle bearings allow for larger axle diameter through the bearing for increased strength
• California Residents: WARNING

Currie Enterprises Currie 60 Front Crate Axle Assemblies

From $7,500.00

• Currie 60 high-pinion radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Large diameter outer pinion bearing (right) is designed for the demands of reverse rotation/high pinion housings. Stock low pinion bearing (left)
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminate oil starvation issues
• Large 3” diameter .375” thick wall axle tubes (left) are more than twice as strong as the stock Dana® 44 (right)
• Upper control arm mounts feature rebuildable Johnny Joints® for improved suspension articulation
• Big 13.250 inch diameter vented rotors (+1.3 inches larger than stock) provide the increased brake torque required for stopping large tires
• Lower control arm mounts are one piece construction with integrated skid plates to help fend off bracket seeking rocks
• California Residents: WARNING

Currie Enterprises Currie Extreme 60 Front Crate Axle Assemblies

From $9,850.00

• Currie Extreme 60 stage-2 high-pinion nodular iron center section is simply the strongest 60 series casting we offer, with 9 lbs. more reinforcement in critical areas over the already strong Stage-1 center section
• Radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Ring gear load bolt eliminates deflection, to dramatically increase the torque handling capacity
• Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys have trouble reading a tape measure
• Currie Performance 35-spline 4340 chrome moly inner and outer axles for superior end to end strength
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and extending bearing life
• Currie nodular iron differential cover with integrated upper control arm mount features rebuildable Johnny Joints® for superior articulation and service life
• Currie Currectlync® 1 5/8” diameter heat treated Chromoly tie rod for unsurpassed strength and reliability
• Big 13.250 rotors (+1.3 inch over stock) and large dual piston calipers provide the stopping power required for 37 inch and larger tires
• California Residents: WARNING

Currie Enterprises Currie 70 Front Crate Axle Assemblies

From $15,352.95

Currie Enterprises Currie 70 Rear Crate Axle Assemblies

From $14,000.00

Milestar Patagonia M/T Tires

From $314.00

• Milestar Patagonia M/T Tires
• Designed to be at home rock crawling, exploring the desert, mud bogging, playing in the dunes, or a casual drive through mountain trails