Synergy Manufacturing Bracket Kit

From $200.00

• Easy installation
• 2.0 inch reservoir mounts sold separately
• Extended bracket measures 17 inch from bottom of bracket to center of bolt hole
• Made in the USA
• California Residents: WARNING

Synergy Manufacturing Front Air Bump Bracket Kit

From $140.00

Synergy Manufacturing Heavy-Duty Replacement Transmission Cross Member

From $315.00

• 3.6L and 3.8L gas engines with either automatic or manual transmissions
• Laser cut and CNC formed from 3/16 inch crush resistant Grade 50 A-572 steel plate
• Fully boxed construction with internal gusseting provides maximum strength where it counts
• Compatible with stock and most aftermarket skid plates
• Made in the U.S.A
• California Residents: WARNING

Synergy Manufacturing Control Arm Kit with Fixed Length Lower Control Arms

From $1,520.00

Synergy Manufacturing Front/Rear Brake Line Kit

From $200.00

• Front and rear DOT approved brake line kit
• Features a special Kevlar liner in addition to the stainless steel braided cover
• They meet the strict guidelines of the U.S. Dept. of Transportation (D.O.T.) MVSS
• Made in the U.S.A
• California Residents: WARNING

Synergy Manufacturing HD E-Coated U-Bolt for 3.50 Inch Axle Tubes

From $25.00

• Axle U-Bolt Kit
• California Residents: WARNING

Synergy Steering Upgrades and Drag Links

From $450.00

• Requires use of Synergy Jeep JK Front Track Bar Bracket (#SYN8055) when flipping the drag link to the top of the knuckle. Requires TRE adapter (#SYN8001-03-01) to flip drag link. Requires a maximum 4-3/4 inch backspace wheel or wheel spacer with factory wheel setup. Can be used in factory position on bottom of steering knuckle Tie Rod and Drag Link both come with Synergy's own HD Metal on Metal Tie Rod Ends, SYN4131-L. Synergy Double Adjuster Sleeve allows adjustment of tie rod length without removing it from the vehicle.
• California Residents: WARNING

Synergy Suspension Joints and Rod Ends

From $60.00

• Synergy Manufacturing products & systems have been designed by real engineers with 10+ years of suspension design & experience in the off road industry. All Synergy products are designed with the use of the latest CAD engineering software to ensure the highest level of fit, finish, and performance.
• California Residents: WARNING

Synergy Track Bar Brackets

From $30.00

• Bracket can be trimmed to desired height to adjust the mounting position of the track bar to alighn the track bar and drag link in the same plane.
• California Residents: WARNING

Synergy Ball Joint Dust Boots

From $10.00

• Synergy Manufacturing products & systems have been designed by real engineers with 10+ years of suspension design & experience in the off road industry. All Synergy products are designed with the use of the latest CAD engineering software to ensure the highest level of fit, finish, and performance.
• California Residents: WARNING

AirLift LoadLifter 7500 XL Air Spring Kits

From $728.99

• Up to 20% more air spring volume than LoadLifter 5000 air springs
• Air Lift-exclusive upper and lower roll plates protect the air springs from possible abrasion and increase load capacity up to 10%
• Most kits use the existing holes in the vehicle’s frame for a bolt-on installation – no drilling required
• Easy to install with illustrated installation manual
• End caps made of ultra high-strength, corrosion-proof, nylon composite which is as strong as steel but weighs less and will not rust
• All kits are compatible with most 5th wheel and gooseneck hitches
• California Residents: WARNING

Synergy Manufacturing Steering Stabilizer Clamps

From $25.00

Synergy Manufacturing Wheel Spacer Studs

From $5.00

• Designed specifically to fit Synergy Wheel Spacers
• Sold individually