Rubicon Express CVO Drive Shafts

From $359.99

• Spicer drive shafts and components are as good as they get. Atlas transfer cases and any other 1310 series CV yoke. Measurements are taken center to center on the u-joint with the slip stub at the center of it's travel. measure your vehicle on the ground in the running position to get correct length.
• California Residents: WARNING

Rubicon Express CVF Drive Shafts

From $369.99

• Spicer drive shafts and components are as good as they get.
• Measurements are taken from flange face to center of the rear u-joint with the slip stub at the center of it's travel. measure your vehicle on the ground in the running position to get correct length.
• California Residents: WARNING

G2 Axle & Gear Drive Shafts

From $330.00

• Heavy-Duty 1 Ton Upgrade
• Made from heavy duty D.O.M. Tubing for strength
• Includes larger solid-body 1350 Series U-Joints for durability
• Dynamically balanced to eliminate vibration
• California Residents: WARNING

Dana Spicer Ultimate Dana 60 Axle Assemblies

From $8,499.99

• The strongest, most robust axle assembly on the market
• Massive Spicer SPL 70 u-joints—exclusive to Dana
• Provides optimal performance for lifted vehicles with larger tires
• Improved “rock solid” seals for optimal protection from environmental contamination
• Manufactured from cold-forged steel
• Spicer 35 spline SAE-4340 nickel chromoly steel axle shafts
• Warn 35 spline hub locks
• Allowing for wheel bearings to be serviced individually
• Easier to repair and service than unit bearing design
• High-strength, heavy gauge brackets
• Cover face rotated back for greater ground clearance
• Reinforced ribbing on bottom of carrier to prevent hang-ups on rocks or rough terrain
• Selectable electronic locking differentials
• Precision-forged gears offer ideal meshing, strength and durability
• Upper and lower control arms in same location as OE
• Better fit, less adjustment on control arm
• Genuine Made in the USA Spicer® 10" (256 mm) ring and pinion gear
• Precision heat treated for optimal hardness and durability
• Face hobbed for precise mating of gear teeth and a quieter ride
• Lapped to reduce noise and heat
• Spicer 1350 Strap-style/Half-round end yoke
• Axle tubes: 3.5" tube diameter/.370" wall thickness
• Helps prevent steering from being knocked out of alignment
• California Residents: WARNING

Fabtech Drive Shafts

From $486.45

• Drive Shaft
• Heavy Duty
• California Residents: WARNING

Currie Enterprises Currie 60 Rear Crate Axle Assemblies

From $5,300.00

• Currie 60 high-pinion, radius bottom center section greatly improves obstacle slide-over by presenting a smooth curve rather than the sharp edge found on other 60 housings
• Highest measured ground clearance of any 60 on the market (and that’s including the integrated skid plate), guess the other guys can’t read a tape measure
• Integrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates
• Large diameter pinion bearings to handle the increased load of reverse geometry gears
• High volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues
• Large 3-inch diameter .375 thick axle tubes deliver superior strength without sacrificing ground clearance or being overweight
• Currie Performance 40-spline 4340 chrome moly semi-floating axles, the largest and strongest standard axle in the industry
• Massive Set 80 axle bearings allow for larger axle diameter through the bearing for increased strength
• California Residents: WARNING

Yukon Gear & Axle Drive Shafts

From $1,099.89