Synergy Manufacturing High Steer Drag Link

From $450.00

TeraFlex Falcon Series Shocks

From $1,705.99

• JK specific reservior locations
• Increases vehicle stability
• Improved dynamic roll control
• Optimized fitment for clearance during full suspension travel and articulation
• Front offset stud design creates additional frame clearance
• Piggyback design increases fluid flow by 6x over restricting reservoir hose designs
• California Residents: WARNING

TeraFlex Leveling Kits

From $115.99

• .5" up to 2" options
• TeraFlex has the perfect solution to level your vehicle if it is dipping in the front from the weight of a winch, sagging, or to level out a loaded vehicle
• These spacers are designed to work in stock configuration, or with a lifted vehicle
• All spacers are sold individually
• California Residents: WARNING

Synergy Manufacturing Wheel Spacers

From $110.00

• Wheel hub centric for increased strength (-H part numbers only)
• CNC machined from billet 6061-T6 aluminum
• Features corrosion resistant red anodizing
• Can be used with factory or after market wheels
• Adapters are 1.50" wide
• Includes Loctite
• Sold as a pair

Synergy Manufacturing Ball Joints

From $250.00

TeraFlex Flex Control Arms

From $1,239.99

• FlexArms allow custom pinion and caster angles to be set for proper alignment, they also are used to re-center the axle in the wheel well for proper suspension movement, and to adjust wheelbase length
• California Residents: WARNING

TeraFlex Performance Big Rotor Kit

From $365.99

• Performance Big Rotor Kit
• 2 and 4-door models
• Reuses factory brake caliper and pads
• 13.3" mill-balanced rotors
• Dual wheel bolt pattern
• California Residents: WARNING

TeraFlex Steering Stabilizer Kits

From $301.99

• Mounting Brackets
• Hardware Kit
• California Residents: WARNING

Synergy Manufacturing Tie Rods

From $350.00

TeraFlex Swaybar Quick Disconnects

From $12.99

• TeraFlex Quick Disconnects are the leader in the industry
• The sway bar link uses a large polyurethane ball and pin for easy sway bar link removal
• When connected for street use the link provides immediate reaction during sway bar loading to eliminate excess play
• California Residents: WARNING

TeraFlex Nebo Roof Racks

From $101.99

• Sleek low profile design for unobtrusive aesthetics and clean aerodynamics for a quiet ride
• Composite supports and trim parts are molded to match the subtle curvature of the hard top
• Extruded aluminum construction for reduced weight
• Extra thick architectural grade UV resistant hard anodizing
• Fasteners coated to OEM specifications for superior corrosion/rust resistance
• Rack cargo load is fully supported by factory sport bar
• Unique easy to reach access holes allow for quick hard top removal with only 4 additional mounting fasteners to loosen
• 4 T-slot channels on main rail for a variety of mounting points
• Optional Slat kit sold separately for additional mounting options
• Molded in hooks on slat mounts to secure light loads
• California Residents: WARNING

Synergy Manufacturing Axle Housing Inner Sleeve Kit

From $150.00

• Designed to increase the strength of the front Axle housing which is prone to bending when larger off road tires are installed and used off road
• Inner Axle Sleeves add a 57% increase in strength over stock
• The stock axle housing must be drilled and plug welded for installation
• California Residents: WARNING

TeraFlex 9550 VSS Shocks

From $330.99

• The VSS gas shock uses a twin-tube shock design
• Triple-chromed rod to ensure extended troublefree operation.
• California Residents: WARNING

TeraFlex CRD60 HD Axle Assemblies

From $2,620.99

• Tera CRD60 specific high-pinion rear axle housing design
• HD bearing caps increase rigidity and reduce ring and pinion distortion
• Constant Radius Design (CRD) provides maximum ground clearance regardless of pinion angle
• Built-in “skimmer” cuts ring gear oil halo and forces it into the pinion bearings
• Outer pinion bearing pocket features a renewable oil reservoir that sends cool oil to the pinion bearing
• Oversized outer pinion bearing handles increased torque and high-load conditions
• High-capacity housing holds maximum amount of oil
• Asymmetric housing design for extra-long tube side strength
• Pre-installed inner axle seals
• Ductile cast iron housing with increased rib gussets
• HD ductile iron differential cover with increased cover mounting area
• Integrated lower control arm skid plates
• High-flow oil passages
• Bottom oil drain hole for simple fluid changes
• Reinforced rear track bar mount with multiple mounting locations
• UV protected triple-stage powder coat for corrosion resistance
• 1/4”-thick CNC laser cut axle brackets for extreme strength
• Pre-installed upper control arm bushings
• Proper pinion angle for lifted applications
• Features a raised pinion angle and raised track bar bracket
• Pre-tapped hole on spring perch for bump stop extensions
• Pre-drilled holes for limit straps and lower spring retainers
• Retains all ESP, ABS, and speedometer sensor capability
• 100% engineered, designed, and built in the USA with new components

TeraFlex Extreme HD Drag Link Kit

From $15.99

• The TeraFlex HD drag link kit is designed for extreme conditions that typically will cause factory steering components to bend and fail
• California Residents: WARNING

TeraFlex High Steer System

From $1,097.99

• Includes tie rod/drag link with one ton tie rod ends
• Tapered inserts
• Pitman arm
• HD cast high steer knuckle
• For use with LCG Lift Kits
• California Residents: WARNING

TeraFlex Rzeppa Factory Replacement CV Kit

From $184.99

• TeraFlex has created the High Angle Rzeppa Factory Replacement CV Joint Kit to help you retain your driveline
• With the High Angle CV housing, it can decrease the boot failure that's commonly seen in taller lifts
• Included in the kit are socket head bolts, the CV joint assembly, a 6 mm Allen wrench, the high angle CV housing boot and the cap, the bolt flanges, and low friction CV grease
• California Residents: WARNING

Synergy Manufacturing Skid Plates

From $1,335.00

• Jeep skid plates manufactured from 3/16" crush resistant Grade A-572 Steel plate
• Flush mounted hardware provides a 100% smooth skid surface
• Premium powdercoat finish for maximum corrosion resistance
• Allows access to drain plug without removal
• Made in the USA
• California Residents: WARNING

TeraFlex SpeedBump Bump Stops

From $148.99

• These innovative TeraFlex SpeedBump Bump Stops meet the demand of high-performance driving
• Reducing this impact increases driver ability to maintain vehicle control as well as reduces the risk of bending an axle housing tube
• Other features include performance-tuned closed-cell nitrogen charged microcellular polyurethane technology that will not fade or dissipate under extended heavy use to maintain its progressive nature
• California Residents: WARNING

Synergy Manufacturing Tie Rod Clamps

From $75.00

• CNC machined from 1020 DOM material
• 100% bolt on
• Zinc plated for corrosion resistance
• Made in the U.S.A
• California Residents: WARNING

TeraFlex Skid Plates

From $11.99

• Jeep skid plates designed to increase overall ground clearance by replacing factory skid plate
• Manufactuered with Stronger and Heavier 1/4" guaged materials
• Installation hardware included
• California Residents: WARNING

TeraFlex NP231 Extreme Short Shaft Kit

From $399.99

• Extreme Short Shaft Kit
• With 231 transfer case
• Eliminates slip yoke
• Requires a longer CV style drive shaft
• California Residents: WARNING

Synergy Manufacturing Front Track Bar & Sector Shaft Brace Kit

From $275.00

• Front Track Bar & Sector Shaft Brace Kit
• 2 and 4-door models
• Includes SYN8069-01 & SYN8069-02
• Steering Sector Brace
• Track bar brace
• Laser cut and CNC bent from 3/16" high strength steel
• Gray powder coat finish for maximum corrosion resistance
• Bolt on installation
• Made in the USA
• California Residents: WARNING

TeraFlex Differential Covers

From $115.99

• Designed to offer extreme protection from rocks, obstacles and other debris on the trail
• Covers are cast from the same high-strength ductile-iron as our their axle housings
• Features a large diameter fill tube/inspection port at the top to accommodate a funnel or gear oil bottle pour spout
• Fluid level port doubles as a mid-height inspection port
• California Residents: WARNING